100% Free

No Scanner Needed

Carly logo
Prices

vincentkoch2

VW Fox Diesel ECU Failure Causing Power Loss Issues

My 2008 VW Fox diesel recently started showing signs of poor engine performance with significantly reduced power output. The error memory shows stored faults, and I suspect the engine control unit might be failing. Has anyone dealt with similar ECU problems on this model? I would like to know if the control system needed replacement or if there were other solutions. What diagnostic steps did your workshop take to fix the issue, and what were the repair costs? The automotive electronics seem otherwise normal, but I want to be sure before deciding on repairs.

Summary of the thread

A 2008 VW Fox diesel is experiencing power loss issues, suspected to be due to ECU failure, with fault codes P0605 and P0700 indicating control system problems. Initial diagnostics showed unstable voltage readings from the ECU, leading to suggestions of either replacement or repair. A similar case with a VW Polo revealed that ECU repair, involving cleaning and resoldering corroded connections, was successful and cost-effective. Before opting for a costly replacement, it's advised to inspect ground connections, wiring harness, and ECU seals for potential issues. A specialist will inspect the ECU for possible repair, offering a more economical solution.

Did this summary help you solve your problem?

4 comment(s)

majaice1

As someone with moderate experience working on VWs, I encountered a similar issue with my 2006 VW Polo diesel. The symptoms matched yours exactly, reduced power and stored fault codes in the engine control system. Initially, I suspected a complete computer module failure, but after having car diagnostics performed, the workshop discovered it was actually just a faulty main relay. This component affects the entire engine control system and can mimic symptoms of ECU failure. The repair process involved: 1. Full system diagnostic scan 2. Testing the power supply to the engine control unit 3. Identifying the faulty relay 4. Replacing the component 5. Performing a system reset Total cost was 120€ including parts and labor. The fix restored full engine performance and cleared all fault codes. Before suggesting specific solutions, it would help to know: What specific fault codes are stored? Does the issue occur when the engine is cold or warm? Have you noticed any other electrical issues? Are there any other warning lights on the dashboard? This could help determine if you are dealing with the same root cause or if your engine control system has a different issue.

vincentkoch2 (community.author)

Last service was performed 2 months ago at 22943km. The fault codes are P0605 and P0700, both pointing toward the ECU problems you mentioned. The issues appear consistently regardless of engine temperature. The check engine light stays on continuously. When running car diagnostics, the workshop tested voltage outputs and found unstable readings from the computer module. They suggested either a full ECU replacement or repair of the existing unit. The engine control performance has gotten worse over the past week. Getting a quote for 950€ for a new unit seems steep. Wondering if rebuilding the control system might be a more cost-effective solution given the age and mileage of the vehicle. Has anyone tried repairing rather than replacing their engine control unit with success?

majaice1

Thanks for providing those specific fault codes, they do point to internal ECU problems, but my experience with my VW Polo suggests it might not require a complete replacement like I initially thought. After dealing with similar control system issues, I first tried the ECU repair route. The repair specialist found corroded connections on the circuit board inside the engine control unit. The total repair cost was 380€, which included cleaning, resoldering connections, and recalibrating the unit. The unstable voltage readings you mentioned were exactly what my car diagnostics showed. However, before committing to any expensive repairs, have your workshop check: 1. The ground connections around the ECU 2. The wiring harness for any signs of water damage 3. The ECU housing seal integrity These checks helped identify the root cause in my case. The vehicle electronics were affected by moisture infiltration through a deteriorated seal, leading to internal corrosion. The repair has held up perfectly for 2 years now, making it a much better value than full replacement. If your ECU shows similar internal issues, I would recommend trying the repair option first.

vincentkoch2 (community.author)

Thank you for all the detailed information and suggestions. After considering the feedback about ECU repair versus replacement, I decided to have a specialist inspect the computer module before committing to the 950€ replacement option. The fault codes P0605 and P0700 combined with the unstable voltage readings definitely indicate control system issues, but getting a second opinion on repair possibilities seems wise. I will have them check the ground connections, wiring harness, and ECU seals as suggested. I contacted a vehicle electronics repair shop that specializes in engine control unit repairs. They quoted 400€ for diagnostic testing, repair, and recalibration if the issue is repairable. This seems more reasonable than full replacement, especially considering the age of my Fox. Will schedule the ECU inspection next week and have them perform a complete system reset after repairs. Hoping this resolves the engine performance issues without needing the more expensive replacement option. Will update once I know more about the actual condition of the control unit.

rmh_community_comment_box_header

community_crosslink_scanner_headline

community_crosslink_scanner_intro

community_crosslink_scanner_title

community_crosslink_scanner_price

community_crosslink_rmh_headline

community_crosslink_rmh_intro

community_crosslink_rmh_title

community_crosslink_rmh_subtitle

community_crosslink_rmh_brand

VW

community_crosslink_rmh_model

FOX