ReinMueller

Electronics problems with the 2018 BMW 2 Series petrol engine: sat nav failure and warning lights

Hello everyone, I have a few problems with my 2018 BMW 2 Series gasoline engine, which now has 27790 km on it. The electronics have recently started to go haywire, my sat nav sometimes won't start at all or only after a while. And sometimes a warning light comes on in the speedometer. Have any of you had similar problems and can tell me how they were solved by your mechanic? My last visit to the garage wasn't that great, so I'd better ask here before I go there again. Thanks in advance!

(Translated from German)

201 comment(s)

I coded my tmps with your machine to show tyre temp as well as pressure. Now there is no readout of either pressure or temp. I have used backup to restore settings to original but that has not worked either

Quotation:
@donniecallander wrote on
I coded my tmps with your machine to show tyre temp as well as pressure. Now there is no readout of either pressure or temp. I have used backup to restore settings to original but that has not worked either

Hello donniecallander, Our Carly Support Team is here to help. Please contact us by clicking on this link and we will get back to you shortly https://support.mycarly.com/hc/en-us/requests/new?ticket_form_id=360000444960 Best regards, CarlyAdminNik

Hello My blé 318d won't start Starter motor running, apparent glow resistor light on dashboard Blue and black relay ok

(Translated from French)

Hello, my G20 often throws the error CD9763 Message (RQ_RPM_BAX, 69.3.4, FX), Timeout: Message (rear axle speed request) from DSC failed in combination with CD9767 Message (RQ_RPM_FTAX, 69.3.4, FX), Timeout: Message (request for front axle speed) from DSC failed. Occurs sporadically when accelerating. Automatic transmission then jerks. Is there an interpretation here?

(Translated from German)

Quotation:
@Jason wrote on
Hello, my G20 often throws the error CD9763 Message (RQ_RPM_BAX, 69.3.4, FX), Timeout: Message (rear axle speed request) from DSC failed in combination with CD9767 Message (RQ_RPM_FTAX, 69.3.4, FX), Timeout: Message (request for front axle speed) from DSC failed. Occurs sporadically when accelerating. Automatic transmission then jerks. Is there an interpretation here?

These error codes suggest a communication issue between the Dynamic Stability Control (DSC) system and the transmission, possibly due to a faulty sensor or wiring issue. I recommend starting with checking the wheel speed sensors and their connections. If the problem persists, a mechanic should inspect the DSC system and transmission. Please keep us updated on your progress.

Replaced the battery on my F25 X3 recently and had this come up after a scan. New battery was installed and registered to the vehicle. Issue went away after clearing codes. It's possible that this issue may get triggered by a battery on its way out.

Quotation:
@MrRobot wrote on
Replaced the battery on my F25 X3 recently and had this come up after a scan. New battery was installed and registered to the vehicle. Issue went away after clearing codes. It's possible that this issue may get triggered by a battery on its way out.

It's good to hear that the issue was resolved after replacing and registering the new battery. If any similar issues arise again, it might be worth checking the battery connections to ensure they are secure and free of corrosion. If you have any further questions or encounter any other issues, feel free to ask.

I had a speedometer control unit failure on my bmw x5 f15 today, so I checked the fuse. Was of course not the fault, whereupon I disconnected the battery for 1 hour as it can sometimes happen that the control unit hangs up. Lo and behold, problem solved, window lifter taught again and pano roof.

(Translated from German)

Quotation:
@Michix5 wrote on
I had a speedometer control unit failure on my bmw x5 f15 today, so I checked the fuse. Was of course not the fault, whereupon I disconnected the battery for 1 hour as it can sometimes happen that the control unit hangs up. Lo and behold, problem solved, window lifter taught again and pano roof.

It's great to hear that disconnecting the battery resolved the issue with your speedometer control unit. If the problem reoccurs, it might be worth checking the connections to the control unit for any loose or corroded contacts. If you have any further questions or need assistance, feel free to ask.

E39 525d 2002 turn key in ignition to position 1. Lights on the dashboard heater coil shows warming up when times out turn ignition to position 2. to start the engine and just a contact click noise doesn’t start and the dashboard lights go out

Join the discussion now: