ReinMueller

Electronics problems with the 2018 BMW 2 Series petrol engine: sat nav failure and warning lights

Hello everyone, I have a few problems with my 2018 BMW 2 Series gasoline engine, which now has 27790 km on it. The electronics have recently started to go haywire, my sat nav sometimes won't start at all or only after a while. And sometimes a warning light comes on in the speedometer. Have any of you had similar problems and can tell me how they were solved by your mechanic? My last visit to the garage wasn't that great, so I'd better ask here before I go there again. Thanks in advance!

(Translated from German)

201 comment(s)

I have a 2015 BMW 535i, 133k miles. I have several issues and one is the Air Condition clutch is not engaging (have Shay replaced the compressor, ac lines, had the system vacuum and serviced by a pro, have replaced the IKHA panel and AUC sensor to no avail. Code I’m getting is E17429

Quotation:
@clarkalea wrote on
I have a 2015 BMW 535i, 133k miles. I have several issues and one is the Air Condition clutch is not engaging (have Shay replaced the compressor, ac lines, had the system vacuum and serviced by a pro, have replaced the IKHA panel and AUC sensor to no avail. Code I’m getting is E17429

Hello, Have you checked whether the voltage for the compressor clutch is OK when the air conditioning is activated? Have you checked whether the fuse for the compressor is OK?

(Translated from German)

Quotation:
@CarlyAdminBenny wrote on
Hello, Have you checked whether the voltage for the compressor clutch is OK when the air conditioning is activated? Have you checked whether the fuse for the compressor is OK?

The fuses are good and have double checked. I am not seeing voltage at the clutch wire. I have verified the wires are good and all have continuity (I am a retired aircraft avionics technician). There is not voltage coming from the top right connector (engine bay, left hand drive, close to the windshield washer line connection, green wire) that on the schematic shows coming from the JBE

Quotation:
@clarkalea wrote on
The fuses are good and have double checked. I am not seeing voltage at the clutch wire. I have verified the wires are good and all have continuity (I am a retired aircraft avionics technician). There is not voltage coming from the top right connector (engine bay, left hand drive, close to the windshield washer line connection, green wire) that on the schematic shows coming from the JBE

Hello, then it looks to me as if the JBE control unit is not transmitting any voltage. Unfortunately, I fear that the control unit itself is defective and needs to be replaced.

(Translated from German)

Quotation:
@CarlyAdminBenny wrote on
Hello, then it looks to me as if the JBE control unit is not transmitting any voltage. Unfortunately, I fear that the control unit itself is defective and needs to be replaced.

Actually I swapped the JBE out with another unit and have the exact same results. No changes on anything. Could this be software related??

Quotation:
@clarkalea wrote on
Actually I swapped the JBE out with another unit and have the exact same results. No changes on anything. Could this be software related??

Hello, Has the control unit not been programmed to the vehicle? Otherwise the whole thing will not work.

(Translated from German)

e60 535d vibrates when stationary and more in D. only in reverse gear it hardly vibrates at all. no engine speed fluctuation or anything else. can you help me a little?

(Translated from German)

Quotation:
@AhmetE60 wrote on
e60 535d vibrates when stationary and more in D. only in reverse gear it hardly vibrates at all. no engine speed fluctuation or anything else. can you help me a little?

This could be due to a variety of issues, such as a problem with the engine mounts, transmission mounts, or a misfire in one of the cylinders. I would recommend starting with a check of the engine and transmission mounts. If these are fine, you may need to have a mechanic diagnose the issue.

Hi when I used the Carly app today after doing the scan the button to move on to look at information did not work

Quotation:
@bluesub wrote on
Hi when I used the Carly app today after doing the scan the button to move on to look at information did not work

Hello, If you have such a problem, please contact our support team directly so that they can help you better. https://support.mycarly.com/hc/de/requests/new?ticket_form_id=360000444960

(Translated from German)

Join the discussion now: